Search
Search
Cancel
anchor&chain
/
/
Lifting & Rigging

PRODUCT CENTER

CATEGORIES

All categories
Dominator Connector for Mining

Dominator Connector for Mining

RUD flat connectors DOMINATOR can be used either vertically or horizontally in round link chain strands. Especially in plough chains acc. to DIN 22252 as well as horizontally as repair connectors in flat link chains acc. to DIN 22255 RUD connectors DOMINATOR are used. Product Category:Mining ChainMake an Inquiry Specifications: Product Parameter: Product Introduction Bi-Lock Connectors(for vertical and horizontal use) BI-lOCK connectors have been specifically desigened to join together round link mining chains in either the horizontal or vertical plane,allowing the connectors to be used in both AFC and plough haulage system applications. Special material seletion combined with close tolerance machining ensures the connector is easily assembled and has a strength greater than the minimum requirements of chain to DIN22252/2 of a comparable size. Adopting Parsons chain Thchnology,the mechanical properties meet the requirements of DIN22258 Part 1 Fatigue test-70,000 cycles min. Mean stress 150N/mm2 . Amplitude±100N/ mm2  Impact KV Test-55J.min.(70J Typical) Refer to DIN22258:2003 part 1 for verification methods and procedures. Assembly and Maintenance An instruction leaflet is supplied with each BI-LOCK connector which gives guidance on correct assembly and maintenance. ·Ensure the mating surfaces and locking barrel are clean and free from dust. ·Once half links and locking barrel are assembled insert locking pin ·Do not interchange components between connectors ·Regularly check for wear or damage ·Fully examine every 3 months or 1M tones conveyed whichever is the sooner.(For BSL use,examine monthly).
Dominator Connector for Mining
Block Connector POWERBLOCK

Block Connector POWERBLOCK

RUD block type connectors POWERBLOCK run vertically over sprockets and are used in high performance mining applications. Product Category:Mining ChainMake an Inquiry Specifications: Product Parameter: Product Introduction V-Lock Connectors(for vertical use only) V-Lock connectors have been specifically designed for joining together mining chains of either round link or compact configuration and have strength 10% greater than connectors designed for use with DIN quality grade 2 chain. Improved performance has been achieved by careful selection of the steel which is unique to parsons and special heat treatment during the manufacturing process.Each connector is additionally differentially heat treated ti ensure the connector sied hardness level is limited to a maximum of HB 363.This ensures maximum resistance to potential rubbing cracks and also further enhances the fatigue life performance. V-LOCK connectors are only for use in the vertical plane and are dimensionally in accordance with DIN22258:2003 part 3. They are extremely sprocket friendly and are lighter in weight compared with the equivalent chainlock connentor. Fatigue Test-100,000 cycles min.(>120,000 typical). Mean stress 150N/mm2 . Amplitude±100N/ mm2  Impact KV Test-55J.min.(90J Typical ) Refer to DIN22258:2003 part 3 for verification methods and procedures Assembly and Maintenance An instruction leaflet is supplid with each V-LOCK connector which gives guidance on corrent assembly and maintenance. Key points are: ·only fit in the vertical plane ·Ensure that mating surfaces are clean and assemble carefully noting the correct direction of travel indicated by an arrow on the top face of the connector ·Do not interchange components between connectors ·Ensure the two sets of tension pins are fully inserted ·Regularly check for wear and damage ·Always fit new tension pins when re-assembling the connector ·Fully examine every 3 months or 1m tones conveyed whichever is the sooner.(For BSL use,examine monthly).
Block Connector POWERBLOCK
Single Plane Chain Connectors TK

Single Plane Chain Connectors TK

TK Connectors: The mechanical properties are at least the equivalent of DIN 22258 Part 2. Chainlock connectors(for horizontal use only) CHAINLOCK connectors have been specifically designed for joining together Xtra quality mining chain and have compatible strength.This is 25% greater than connectors designed for use with DIN quality grade 2 china of either round or flat link configuration. This Xtra performance has been achieved through careful choice of materials and heat treatment whilst keeping the dimensional properties within those specified in DIN 22258:2003 part 2. This will ensure that the connectors-which must be installed in the horizontal plane of the chain only-will safely negotiate sprockets that have been designed in accordance with this specification. CHAINLOCK connectors can also be used with DIN quality grade 2 chains having the advantage of higher strength thus giving an additional     Fatigue Test-100,000 cycles min.(>150,000 trpical). Mean stress 150N/mm2 . Amplitude卤100N/mm2 lmpact KV Test-55J.min.(70J Typical) Refer to DIN22258:2003 part 2 for verification methods and procedures Assembly and Maintenance An instruction leaflet is supplied with each CHAINLOCK connector which gives guidance on correct assembly and maintenance. Key points are: Only fit in the horizontal plane Assemble the spacer into the connector body so that the location marks are aligned. Do not interchange components between connectors Ensure the securing screw is correctly tightened to appropriate torque stated below. Regularly check for wear and damage Fully examine every 2 months or 1 M tones conveyed whichever is the sooner.(For BSL use, examine monthly). Always fit a new securing screw when re-assembling the connector
Single Plane Chain Connectors TK
Connecting Links For Hatch Cover Driving Chain

Connecting Links For Hatch Cover Driving Chain

Connecting links for joint chains. Available in stainless steel or galvanized steel. Various measures. The LIG Grade 30 Oval Galvanised Chain Connecting Link is ideal for fitting two pieces of chain together. This fully hot dip galvanised connecting link is quality-made by Peerless LIG, CHINA. Specifically designed for joining a short link to a mild steel chain. To install, all you need is a hammer and a pair of pliers. Just peen the pins together to connect two pieces of chain and you're good to go. LIG Grade 30 Oval Galvanised Chain Connecting Link Features: Designed for joining short link mild steel chain Fully hot dip galvanised 4:1 minimum design factor Quality connecting links from Peerless LIG, CHINA   Also known as hammer locks and sling links, assemble by hammering a pin through the center. They're often used to connect the legs of chain sling to a master link. Grade 120 connectors are the strongest links we offer. When used with chain of the same grade, they are approximately 20% stronger than Grade 100 links and about 35% stronger than Grade 80 links. They're powder coated for mild corrosion resistance. Grade 100 connectors are approximately 20% stronger than Grade 80 links when used with chain of the same grade. Grade 63 connectors are approximately 60% as strong as Grade 80 links when used with chain of the same grade. They're stainless steel and have excellent resistance to salt water and chemicals. Note: Connecting links are for vertical lifting only.
Connecting Links For Hatch Cover Driving Chain
上一页
1
2
12
anchor&chain
anchor&chain

Company phone:

+86-514-89799469

anchor&chain

Company email: 

846051730@qq.com

anchor&chain

Company address:

No.43 Jiangyang Road,Development Zone, Yangzhou City, Jiangsu Province, China.

Copyright © YANGZHOU LIG MARINE MACHINERY CO.,LTD.     All Rights Reserved.  苏ICP备19007055号-2     Powered by www.300.cn

anchor&chain